東華大學圖書館 |

語系: 繁體中文

說明(常見問題)

回圖書館首頁

手機版館藏查詢

登入

回首頁

切換: 標籤 | MARC模式 | ISBD

The effects of the processing parame...

Ramrattan, Sam Nerone.

FindBook

Google Book

Amazon

博客來

The effects of the processing parameters on the laser machining of a green china ceramic.

紀錄類型:	書目-電子資源 : Monograph/item
正題名/作者:	The effects of the processing parameters on the laser machining of a green china ceramic./
作者:	Ramrattan, Sam Nerone.
出版者:	Ann Arbor : ProQuest Dissertations & Theses, : 1989,
面頁冊數:	141 p.
附註:	Source: Dissertation Abstracts International, Volume: 51-01, Section: A, page: 9700.
Contained By:	Dissertation Abstracts International51-01A.
標題:	Industrial arts education. -
電子資源:	http://pqdd.sinica.edu.tw/twdaoapp/servlet/advanced?query=9014944

The effects of the processing parameters on the laser machining of a green china ceramic.
Ramrattan, Sam Nerone.

The effects of the processing parameters on the laser machining of a green china ceramic. - Ann Arbor : ProQuest Dissertations & Theses, 1989 - 141 p.

Source: Dissertation Abstracts International, Volume: 51-01, Section: A, page: 9700.

Thesis (Ph.D.)--Iowa State University, 1989.

The purpose of this study was to investigate the quality of the cut, the thickness of the heat-affected zone, and the amount of dross produced by laser cutting green china ceramics.Subjects--Topical Terms:

3173045
Industrial arts education.

The effects of the processing parameters on the laser machining of a green china ceramic.
LDR:02701nmm a2200325 4500 001 2154044
005 20180322121333.5
008 190424s1989 ||||||||||||||||| ||eng d
035 $a (MiAaPQ)AAI9014944
035 $a AAI9014944
040 $a MiAaPQ $c MiAaPQ
100 1 $a Ramrattan, Sam Nerone. $3 3341767
245 1 4 $a The effects of the processing parameters on the laser machining of a green china ceramic.
260 1 $a Ann Arbor : $b ProQuest Dissertations & Theses, $c 1989
300 $a 141 p.
500 $a Source: Dissertation Abstracts International, Volume: 51-01, Section: A, page: 9700.
500 $a Supervisor: John Newton Riley.
502 $a Thesis (Ph.D.)--Iowa State University, 1989.
520 $a The purpose of this study was to investigate the quality of the cut, the thickness of the heat-affected zone, and the amount of dross produced by laser cutting green china ceramics.
520 $a This study seeks an alternative method to cut greenware, which will reduce the high rate of defect found in conventional punching and trimming. The study was centered on laser cutting and in any machining process the surface properties of the material were considered. This study provides the processing parameters relating to one type of china greenware, but the information gathered will be important in the development of any new laser cutting process for green china ceramic.
520 $a The independent variables that were manipulated in this experiment were: moisture content of the greenware, feed rate at which samples are cut, and power of the laser beam. Specimens were laser cut at high, medium, and low levels of each of the independent variables. The investigation was concerned with the effect(s) the independent variations may have on the following dependent variables: quality of cut measured in micro inch, thickness of the heat-affected zone measured in thousandths of an inch, and weight of dross measured in thousandths of a gram.
520 $a Statistical analyses were performed on the sets of data obtained after laser cutting. Greatest attention was given to qualifying and quantifying the effects and any relationship with respect to the quality of cut, the thickness of the heat-affected zone, and the amount of dross produced.
520 $a The results of this study indicated that the higher the moisture content the better the quality of cut. Low feed rate and/or high power causes the widest heat-affected zone. The higher the power the greater the weight of dross.
590 $a School code: 0097.
650 4 $a Industrial arts education. $3 3173045
650 4 $a Industrial engineering. $3 526216
690 $a 0521
690 $a 0546
710 2 $a Iowa State University. $3 1017855
773 0 $t Dissertation Abstracts International $g 51-01A.
790 $a 0097
791 $a Ph.D.
792 $a 1989
793 $a English
856 4 0 $u http://pqdd.sinica.edu.tw/twdaoapp/servlet/advanced?query=9014944