東華大學圖書館 |

Language: English

Help

回圖書館首頁

手機版館藏查詢

Back

Switch To: Labeled | MARC Mode | ISBD

Defect Detection on Rail Base Area U...

Shrestha, Survesh.

Linked to FindBook

Google Book

Amazon

博客來

Defect Detection on Rail Base Area Using Infrared Thermography.

Record Type:	Electronic resources : Monograph/item
Title/Author:	Defect Detection on Rail Base Area Using Infrared Thermography./
Author:	Shrestha, Survesh.
Published:	Ann Arbor : ProQuest Dissertations & Theses, : 2020,
Description:	85 p.
Notes:	Source: Masters Abstracts International, Volume: 82-04.
Contained By:	Masters Abstracts International82-04.
Subject:	Mechanical engineering. -
Online resource:	https://pqdd.sinica.edu.tw/twdaoapp/servlet/advanced?query=28023135
ISBN:	9798678159809

Defect Detection on Rail Base Area Using Infrared Thermography.
Shrestha, Survesh.

Defect Detection on Rail Base Area Using Infrared Thermography. - Ann Arbor : ProQuest Dissertations & Theses, 2020 - 85 p.

Source: Masters Abstracts International, Volume: 82-04.

Thesis (M.S.)--Southern Illinois University at Carbondale, 2020.

This item must not be sold to any third party vendors.

This research aims to investigate the application of infrared thermography (IRT) as a method of nondestructive evaluation (NDE) for the detection of defects in the rail base area. Rails have to withstand harsh conditions during their application. Therefore, defects can develop in the base area of rails due to stresses such as bending, shear, contact, and thermal stresses, fatigue, and corrosion. Such defects can cause catastrophic failures in the rails, ultimately leading to train derailments. Rail base defects due to fatigue and corrosion are difficult to detect and currently there are no reliable or practical non-destructive evaluation (NDE) methods for finding these types of defects in the revenue service. Transportation Technology Center, Inc. (TTCI) had previously conducted a research on the capability of flash IRT to detect defects in rail base area based on simulation approach. The research covered in this thesis is the continuation of the same project.In this research, three rail samples were prepared with each containing a notched-edge, side-drilled holes (SDHs), and bottom-drilled holes (BDHs). Two steel sample blocks containing BDHs and SDHs of different sizes and depths were also prepared. Preliminary IRT trials were conducted on the steel samples to obtain an optimal IRT setup configuration. The initial inspections for one of the steel samples were outsourced to Thermal Wave Imaging (TWI) where they employed Thermographic Signal Reconstruction (TSR) technique to enhance the resulting images. Additional inspections of the steel samples were performed in the Southern Illinois University-Carbondale (SIUC) facility. In case of the rail samples, the SDHs and the notched-edge reflectors could not be detected in any of the experimental trials performed in this research. In addition, two more rail samples containing BDHs were prepared to investigate the detection capabilities for three different surface conditions: painted, unpainted, and rusted. The painted surface provided a best-case scenario for inspections while the other conditions offered further insight on correlating the application to industry-like cases.A 1300 W halogen lamp was employed as the heat source for providing continuous thermal excitation for various durations. Post-processing and analysis of the resulting thermal images was performed within the acquisition software using built-in analysis tools such as temperature probes, Region of Interest (ROI) based intensity profiles, and smoothing filters. The minimum defect diameter to depth (aspect) ratio detected in preliminary trials for the steel sample blocks were 1.0 at a diameter of 4.7625 mm (0.1875 in) and 1.5 at a diameter of 3.175 mm (0.125 in). For the inspection of painted rail sample, the longest exposure times (10 sec) provided the best detection capabilities in all sets of trials. The three holes having aspect ratio greater or equal to 1.0 were indicated in the thermal response of the painted and rusted samples while only the two holes having aspect ratio greater or equal to 1.5 were indicated in the unaltered sample. Indications of reflectors were identified through qualitative graphical analysis of pixel intensity distributions obtained along a bending line profile. The results obtained from the painted sample provided a baseline for analyzing the results from the unpainted and rusted rail samples. This provided an insight on the limitations and requirements for future development. The primary takeaway is the need for an optimized heat source. Poor contrast in the resulting image for the unpainted and rusted rail samples is experienced due to both noise and lack of penetration of the heat energy. This could have been due to decreased emissivity values. Moreover, the excitation method employed in this research does not comply with current industry standards for track clearances. Therefore, exploration of alternative excitation methods is recommended.

ISBN: 9798678159809Subjects--Topical Terms:

649730
Mechanical engineering.
Subjects--Index Terms:

Flash Thermography

Defect Detection on Rail Base Area Using Infrared Thermography.
LDR:05173nmm a2200385 4500 001 2281248
005 20210910100651.5
008 220723s2020 ||||||||||||||||| ||eng d
020 $a 9798678159809
035 $a (MiAaPQ)AAI28023135
035 $a AAI28023135
040 $a MiAaPQ $c MiAaPQ
100 1 $a Shrestha, Survesh. $3 3559833
245 1 0 $a Defect Detection on Rail Base Area Using Infrared Thermography.
260 1 $a Ann Arbor : $b ProQuest Dissertations & Theses, $c 2020
300 $a 85 p.
500 $a Source: Masters Abstracts International, Volume: 82-04.
500 $a Advisor: Chu, Tsuchin Philip.
502 $a Thesis (M.S.)--Southern Illinois University at Carbondale, 2020.
506 $a This item must not be sold to any third party vendors.
520 $a This research aims to investigate the application of infrared thermography (IRT) as a method of nondestructive evaluation (NDE) for the detection of defects in the rail base area. Rails have to withstand harsh conditions during their application. Therefore, defects can develop in the base area of rails due to stresses such as bending, shear, contact, and thermal stresses, fatigue, and corrosion. Such defects can cause catastrophic failures in the rails, ultimately leading to train derailments. Rail base defects due to fatigue and corrosion are difficult to detect and currently there are no reliable or practical non-destructive evaluation (NDE) methods for finding these types of defects in the revenue service. Transportation Technology Center, Inc. (TTCI) had previously conducted a research on the capability of flash IRT to detect defects in rail base area based on simulation approach. The research covered in this thesis is the continuation of the same project.In this research, three rail samples were prepared with each containing a notched-edge, side-drilled holes (SDHs), and bottom-drilled holes (BDHs). Two steel sample blocks containing BDHs and SDHs of different sizes and depths were also prepared. Preliminary IRT trials were conducted on the steel samples to obtain an optimal IRT setup configuration. The initial inspections for one of the steel samples were outsourced to Thermal Wave Imaging (TWI) where they employed Thermographic Signal Reconstruction (TSR) technique to enhance the resulting images. Additional inspections of the steel samples were performed in the Southern Illinois University-Carbondale (SIUC) facility. In case of the rail samples, the SDHs and the notched-edge reflectors could not be detected in any of the experimental trials performed in this research. In addition, two more rail samples containing BDHs were prepared to investigate the detection capabilities for three different surface conditions: painted, unpainted, and rusted. The painted surface provided a best-case scenario for inspections while the other conditions offered further insight on correlating the application to industry-like cases.A 1300 W halogen lamp was employed as the heat source for providing continuous thermal excitation for various durations. Post-processing and analysis of the resulting thermal images was performed within the acquisition software using built-in analysis tools such as temperature probes, Region of Interest (ROI) based intensity profiles, and smoothing filters. The minimum defect diameter to depth (aspect) ratio detected in preliminary trials for the steel sample blocks were 1.0 at a diameter of 4.7625 mm (0.1875 in) and 1.5 at a diameter of 3.175 mm (0.125 in). For the inspection of painted rail sample, the longest exposure times (10 sec) provided the best detection capabilities in all sets of trials. The three holes having aspect ratio greater or equal to 1.0 were indicated in the thermal response of the painted and rusted samples while only the two holes having aspect ratio greater or equal to 1.5 were indicated in the unaltered sample. Indications of reflectors were identified through qualitative graphical analysis of pixel intensity distributions obtained along a bending line profile. The results obtained from the painted sample provided a baseline for analyzing the results from the unpainted and rusted rail samples. This provided an insight on the limitations and requirements for future development. The primary takeaway is the need for an optimized heat source. Poor contrast in the resulting image for the unpainted and rusted rail samples is experienced due to both noise and lack of penetration of the heat energy. This could have been due to decreased emissivity values. Moreover, the excitation method employed in this research does not comply with current industry standards for track clearances. Therefore, exploration of alternative excitation methods is recommended.
590 $a School code: 0209.
650 4 $a Mechanical engineering. $3 649730
650 4 $a Remote sensing. $3 535394
650 4 $a Automotive engineering. $3 2181195
653 $a Flash Thermography
653 $a Infrared Thermography
653 $a Nondestructive Evaluation (NDE)
653 $a Nondestructive Testing (NDT)
653 $a Rail Base Defect
653 $a Railroad Inspection
690 $a 0548
690 $a 0799
690 $a 0540
710 2 $a Southern Illinois University at Carbondale. $b Mechanical Engineering. $3 1035345
773 0 $t Masters Abstracts International $g 82-04.
790 $a 0209
791 $a M.S.
792 $a 2020
793 $a English
856 4 0 $u https://pqdd.sinica.edu.tw/twdaoapp/servlet/advanced?query=28023135