東華大學圖書館 |

語系: 繁體中文

說明(常見問題)

回圖書館首頁

手機版館藏查詢

登入

回首頁

切換: 標籤 | MARC模式 | ISBD

Coating Characterization with the Qu...

Sturdy, Lauren F.

FindBook

Google Book

Amazon

博客來

Coating Characterization with the Quartz Crystal Microbalance.

紀錄類型:	書目-電子資源 : Monograph/item
正題名/作者:	Coating Characterization with the Quartz Crystal Microbalance./
作者:	Sturdy, Lauren F.
面頁冊數:	151 p.
附註:	Source: Dissertation Abstracts International, Volume: 77-10(E), Section: B.
Contained By:	Dissertation Abstracts International77-10B(E).
標題:	Materials science. -
電子資源:	http://pqdd.sinica.edu.tw/twdaoapp/servlet/advanced?query=10117234
ISBN:	9781339786377

Coating Characterization with the Quartz Crystal Microbalance.
Sturdy, Lauren F.

Coating Characterization with the Quartz Crystal Microbalance. - 151 p.

Source: Dissertation Abstracts International, Volume: 77-10(E), Section: B.

Thesis (Ph.D.)--Northwestern University, 2016.

The quartz crystal microbalance is a sensitive tool that can be used to measure the mass, modulus and phase angle of films of appropriate thicknesses. It is can be applied to systems with very varied properties, from liquid to solid, and under many different conditions. In this thesis its capabilities have been used to study the properties of several different systems of relevance to the coatings, art conservation, and rubber communities, in the process of which new techniques and tools were developed to analyze data and improve QCM data collection and experimental design.

ISBN: 9781339786377Subjects--Topical Terms:

543314
Materials science.

Coating Characterization with the Quartz Crystal Microbalance.
LDR:04986nmm a2200313 4500 001 2079346
005 20170313112135.5
008 170521s2016 ||||||||||||||||| ||eng d
020 $a 9781339786377
035 $a (MiAaPQ)AAI10117234
035 $a AAI10117234
040 $a MiAaPQ $c MiAaPQ
100 1 $a Sturdy, Lauren F. $3 3195017
245 1 0 $a Coating Characterization with the Quartz Crystal Microbalance.
300 $a 151 p.
500 $a Source: Dissertation Abstracts International, Volume: 77-10(E), Section: B.
500 $a Adviser: Kenneth R. Shull.
502 $a Thesis (Ph.D.)--Northwestern University, 2016.
520 $a The quartz crystal microbalance is a sensitive tool that can be used to measure the mass, modulus and phase angle of films of appropriate thicknesses. It is can be applied to systems with very varied properties, from liquid to solid, and under many different conditions. In this thesis its capabilities have been used to study the properties of several different systems of relevance to the coatings, art conservation, and rubber communities, in the process of which new techniques and tools were developed to analyze data and improve QCM data collection and experimental design.
520 $a Alkyd resins, which have been used in artists' paints since the twentieth century, are the subject of the first studies. Alkyds are oil-modified polyesters. These resins are of interest because of their relatively recent use in art and how little is known of the mechanical properties in the early stages of cure. The QCM was shown to be sensitive to the curing process, changes in temperature, and mass change due to exposure to water. Kinetic studies during the first days of curing showed that the curing process can be divided into three regions. The first is dominated by solvent evaporation. In the second, oxygen absorption dominates and the mechanical properties change rapidly. The final stage extends from when the film is touch dry after about a day to years and is characterized by mass loss and continued increases in the modulus. Studying the curing at different temperatures revealed that the reactions do proceed much more rapidly at higher temperatures and an overall energy of activation was calculated for the curing process. The mechanical properties of alkyd resins containing zinc oxide, a white pigment, were studied with the QCM, nanoindentation and dynamic mechanical analysis. These measurements showed increases in the modulus with the inclusion of zinc oxide, and the QCM data showed that the second region started at earlier times as the pigment concentration was increased.
520 $a Linseed oil is one of the starting materials for many alkyd resins and should cure similarly since the primary curing mechanisms are the same. It takes longer to cure than alkyds because it begins with no initial polymerization. Linseed oil was harder to study, as obtaining even films was difficult, multiple peaks at a single harmonic were observed, and the material properties during the early stages of curing led to a region where viscoelastic properties could not be calculated. To facilitate studying linseed oil, a multiple peak fitting method was developed to extract data from unusual peak shapes. With this ability, measurements at short times could be obtained despite poor film quality. Although linseed oil begins as a softer material than alkyds, its curing follows the same patterns as alkyd resins, exhibiting mass gain followed by mass loss, and sharp increases in modulus and decreases in phase angle during the early stages of curing.
520 $a Having demonstrated the ability of the QCM to monitor curing, the QCM was also applied to uncrosslinked rubber systems. Rubbers, like the drying oils, contain double bonds which can react with oxygen, so first the oxidation of these materials was studied. In further studies oxidation was undesirable, so protocols were developed to limit oxidation. Measurements were made of homopolymers at different temperatures and the QCM measurements appear to be consistent with time-temperature superposition results obtained at lower frequencies. Blends of the various rubbers were studied and compared with models. The mechanical properties measured by the QCM were between the Voigt and Reuss predictions for most blends studied. Modeling the expected QCM response of layered rubbers matched the predictions of the Reuss model but not the measured values of the rubber blends, suggesting that the QCM is sensitive to different morphologies. Measurements with the QCM expanded our understanding of a variety of systems and proved to be a useful tool to measure mechanical changes during processes which are difficult to study by other methods.
590 $a School code: 0163.
650 4 $a Materials science. $3 543314
650 4 $a Polymer chemistry. $3 3173488
690 $a 0794
690 $a 0495
710 2 $a Northwestern University. $b Materials Science and Engineering. $3 1058406
773 0 $t Dissertation Abstracts International $g 77-10B(E).
790 $a 0163
791 $a Ph.D.
792 $a 2016
793 $a English
856 4 0 $u http://pqdd.sinica.edu.tw/twdaoapp/servlet/advanced?query=10117234