東華大學圖書館 |

語系: 繁體中文

說明(常見問題)

回圖書館首頁

手機版館藏查詢

登入

回首頁

切換: 標籤 | MARC模式 | ISBD

Direct methanol fuel cell membranes ...

Lee, Jeong Kyu.

FindBook

Google Book

Amazon

博客來

Direct methanol fuel cell membranes from polymer blends.

紀錄類型:	書目-電子資源 : Monograph/item
正題名/作者:	Direct methanol fuel cell membranes from polymer blends./
作者:	Lee, Jeong Kyu.
面頁冊數:	165 p.
附註:	Source: Dissertation Abstracts International, Volume: 66-11, Section: B, page: 6118.
Contained By:	Dissertation Abstracts International66-11B.
標題:	Engineering, Chemical. -
電子資源:	http://pqdd.sinica.edu.tw/twdaoapp/servlet/advanced?query=3196685
ISBN:	9780542407277

Direct methanol fuel cell membranes from polymer blends.
Lee, Jeong Kyu.

Direct methanol fuel cell membranes from polymer blends. - 165 p.

Source: Dissertation Abstracts International, Volume: 66-11, Section: B, page: 6118.

Thesis (Ph.D.)--Case Western Reserve University, 2006.

Proton conducting membranes for a direct methanol fuel cell (DMFC) were prepared from the following polymer blends: Sulfonated poly [bis(phenoxy)phosphazene] (SPOP) - polybenzimidazole (PBI), Nafion - Teflon FEP (copolymer of tetrafluoroethylene and hexafluoropropylene), and Nafion - PBI. Films were made by either solution casting (for SPOP-PBI and Nafion-PBI) or melt processing (for Nafion-FEP). The resulting membranes (50-120 mum in thickness) were evaluated in terms of water swelling, proton conductivity, and methanol permeability. They were also fabricated in membrane-electrode assemblies and tested in a DMFC at 60°C. The proton conductivity and methanol permeability of the membranes were found to be dependent on the blend composition, e.g., ion-exchange capacity of SPOP and wt% of PBI (for SPOP-PBI blends), wt% FEP (for Nafion-FEP), and Nafion protonation degree and wt% PBI (for Nafion-PBI blends). The DMFC performance (maximum power density) with a SPOP-PBI membrane was comparable to that of a Nafion 117 at 1.0 M methanol, but the methanol crossover flux was 2.6 times lower than that of Nafion 117. With blended Nafion-FEP and Nafion-PBI membranes, the current-density/voltage behavior in a DMFC was similar to Nafion, with 1.4 and 1.5 times lower methanol crossover. Significant cost savings can be realized when using the blended films rather than Nafion 117 because they are thinner than Nafion 117 (by a factor of 3.0-3.5) and contain less of the expensive perfluorosulfonic acid polymer. With increasing methanol concentration (up to 10.0 M), the blended membranes exhibited superior DMFC performance and lower methanol crossover fluxes as compared to Nafion 117.

ISBN: 9780542407277Subjects--Topical Terms:

1018531
Engineering, Chemical.

Direct methanol fuel cell membranes from polymer blends.
LDR:02555nmm 2200265 4500 001 1821610
005 20061114121714.5
008 130610s2006 eng d
020 $a 9780542407277
035 $a (UnM)AAI3196685
035 $a AAI3196685
040 $a UnM $c UnM
100 1 $a Lee, Jeong Kyu. $3 1254148
245 1 0 $a Direct methanol fuel cell membranes from polymer blends.
300 $a 165 p.
500 $a Source: Dissertation Abstracts International, Volume: 66-11, Section: B, page: 6118.
500 $a Adviser: Peter N. Pintauro.
502 $a Thesis (Ph.D.)--Case Western Reserve University, 2006.
520 $a Proton conducting membranes for a direct methanol fuel cell (DMFC) were prepared from the following polymer blends: Sulfonated poly [bis(phenoxy)phosphazene] (SPOP) - polybenzimidazole (PBI), Nafion - Teflon FEP (copolymer of tetrafluoroethylene and hexafluoropropylene), and Nafion - PBI. Films were made by either solution casting (for SPOP-PBI and Nafion-PBI) or melt processing (for Nafion-FEP). The resulting membranes (50-120 mum in thickness) were evaluated in terms of water swelling, proton conductivity, and methanol permeability. They were also fabricated in membrane-electrode assemblies and tested in a DMFC at 60°C. The proton conductivity and methanol permeability of the membranes were found to be dependent on the blend composition, e.g., ion-exchange capacity of SPOP and wt% of PBI (for SPOP-PBI blends), wt% FEP (for Nafion-FEP), and Nafion protonation degree and wt% PBI (for Nafion-PBI blends). The DMFC performance (maximum power density) with a SPOP-PBI membrane was comparable to that of a Nafion 117 at 1.0 M methanol, but the methanol crossover flux was 2.6 times lower than that of Nafion 117. With blended Nafion-FEP and Nafion-PBI membranes, the current-density/voltage behavior in a DMFC was similar to Nafion, with 1.4 and 1.5 times lower methanol crossover. Significant cost savings can be realized when using the blended films rather than Nafion 117 because they are thinner than Nafion 117 (by a factor of 3.0-3.5) and contain less of the expensive perfluorosulfonic acid polymer. With increasing methanol concentration (up to 10.0 M), the blended membranes exhibited superior DMFC performance and lower methanol crossover fluxes as compared to Nafion 117.
590 $a School code: 0042.
650 4 $a Engineering, Chemical. $3 1018531
690 $a 0542
710 2 0 $a Case Western Reserve University. $3 1017714
773 0 $t Dissertation Abstracts International $g 66-11B.
790 1 0 $a Pintauro, Peter N., $e advisor
790 $a 0042
791 $a Ph.D.
792 $a 2006
856 4 0 $u http://pqdd.sinica.edu.tw/twdaoapp/servlet/advanced?query=3196685